If the gas isn't lighting properly, it can build up and cause a 'whoosh' noise on the burner. This might be caused by a spark ignition switch and harness that only works sometimes. You can use a multimeter, a tool that checks if electricity can flow through something, to test the spark ignition switches for electrical continuity. This can help you figure out if the assembly is working like it's supposed to.
The fan blade may be bent or misaligned, causing it to make contact with the housing. It is advisable to inspect the fan blade for any signs of damage. Should you observe bending or other deformations, replacing the fan blade will be necessary.
The cooling fan operates to help prevent the range and its important parts from getting too hot. The cooling fan is usually sold as a complete unit. If the fan makes noise when it runs, the motor bearings, fan blade, or blower wheel might be worn out or damaged and will need to be replaced.
The blower motor operates to help prevent the range and its important parts from getting too hot, and it can also help push air outside. The blower motor is usually sold as a complete unit. If the fan makes noise when it runs, the motor bearings, fan blade, or blower wheel might be worn out or damaged and will need to be replaced.
When a surface element switch shorts out, you'll hear a popping noise, and then the switch won't work anymore. Before you replace the switch, you should check to see if the surface element is shorted out.
If the gas doesn't ignite quickly, it can build up and cause a small 'boom' noise in the oven or a 'whoosh' noise on the burner. A broken igniter might be the reason for the gas not igniting quickly. To see if the igniter is broken, watch the igniter when the oven is on. If the igniter glows for more than 90 seconds without igniting the gas flame, it means the igniter is too weak to open the valve. If the igniter is weak, you should replace it. If the igniter doesn't glow at all, use a multimeter, a tool that checks if electricity can flow through something, to test the igniter for continuity. If the igniter doesn't have continuity, you should replace it.
The convection motor powers the convection fan to move the air inside the oven. This movement of air is needed for the oven to distribute heat evenly. If the motor's bearings are bad, the motor might make a rattling noise, or the fan could hit the housing. If the convection fan motor's shaft wobbles or if the motor is making a loud noise, you should replace the convection motor.
If the gas doesn't ignite quickly, it can build up and cause a small 'boom' noise in the oven or a 'whoosh' noise on the burner. The spark module sends high-voltage pulses to the spark igniters and spark electrodes to light the burners. If the spark module isn't working right, the oven or stovetop might not light properly. You should check the spark module for signs of burning or a part that's shorted out. You can also use a multimeter, a tool that checks if electricity can flow through something, to see if voltage is reaching the spark module. If voltage is reaching the module, but the gas isn't igniting quickly, the spark module might be broken and need to be replaced.
If the gas doesn't ignite quickly, it can build up and cause a small 'bang' noise in the oven or a 'whoosh' noise on the burner. The control board sends voltage to the ignition parts to light the burners, so a broken control board might cause the gas not to ignite quickly, though this isn't a common issue. You can check the board for burn marks or other damage, but you should make sure all the other ignition parts are working right before thinking about replacing the control board.
If the gas isn't lighting properly, it can build up and cause a small 'boom' noise in the oven or a 'whoosh' noise on the burner. This might be caused by a spark module that only works sometimes. You can use a multimeter, a tool that checks if electricity can flow through something, to see if voltage is reaching the spark module. If the right voltage is present, and all other oven parts are working normally, the spark module is probably broken and should be replaced.
If the gas isn't lighting properly, it can build up and cause a small 'pop' noise in the oven. This might be caused by a broken oven control board. However, control boards are often wrongly blamed—before replacing the control board, first check parts that usually break more often. If you've made sure that all the other parts are working as they should, then you should replace the control board.
The fan motor spins the fan blade to move the air around. The fan motor is usually sold as a complete unit. If the fan motor's bearings are bad, or if the fan blade or blower is damaged, the fan motor will need to be replaced.